Request Information Download PDF
GT-41076-06VV-Q GT-41076-06VV-Q
Information
Model NumberGT-41076-06VV-Q
DescriptionGT-41076-06VV-Q, ITE Power Supply, Wall Plug-in, Regulated Switchmode AC-DC, , Input Rating: 100-240V~, 50-60 Hz, Blade Options for Q Series Wall Plug-in Power Supplies, Output Rating: 6 Watts, 3-24V in 0.1V increments, Approvals: WEEE VCCI SIQ Ukraine NrCAN RoHS 2 LPS Level V Double Insulation China RoHS CE CB C-Tick CCC cULus Korea (5V Only) Taiwan BSMI CE IP20 PSE PSE PSE India CE
Agency Documentshttp://www.globtek.info/certs/GT-41076/
CE EC-Declaration for MedicalContact GlobTek for more information
CE EC-Declaration for Industrial/Commercial/ITEhttp://globtek.force.com/models/ec_declaration?id=a0O30000007P7ZqEAK
RoHS/RoHS2 Declarationhttp://www.globtek.com/pdf/rohs_cert/a0O30000007P7ZqEAK
REACH Declarationhttp://www.globtek.com/pdf/iso_certificates/REACH.pdf
Conflict Minerals Declarationhttp://www.globtek.com/pdf/conflict-minerals.pdf
Model Parameters
TypeWall Plug-in
TechnologyRegulated Switchmode AC-DC
CategoryITE Power Supply
Input Voltage100-240V~, 50-60 Hz
I/P Amps (A)0.3A
Wattage (W)6
Vout Range (V)3-24
EfficiencyV
Ingress ProtectionIP20
Size (mm)64*40.5*29
EnclosureUser-added image
Rating Table
Model NumberVoltageAmps (A)Watts (W)RFQ
GT-41076-0603326RFQ
GT-41076-0605-1.53.513.5RFQ
GT-41076-0605-0.94.11.24.92RFQ
GT-41076-060551.26RFQ
GT-41076-0609-3.55.51.096RFQ
GT-41076-0609-3.0616RFQ
GT-41076-060990.665.94RFQ
GT-41076-0612120.56RFQ
GT-41076-0615150.46RFQ
GT-41076-0618180.335.94RFQ
GT-41076-0620200.36RFQ
GT-41076-0624240.256RFQ
SpecificationsA) ELECTRICAL SPECIFICATIONS:
01. Input Voltage: Specified 90-264 Vac, Nameplate rated: 100-240Vac
02. Input Frequency: Specified 47-63 Hz, Nameplate rated 50-60Hz
03. Output Regulation: +/- 5% measured at the output connector
04. Line Voltage Regulation: +/- 1% typical measured at output connector
05. Output Ripple (Vp-p): +/-1% or 50 mV whichever is greater, measured at 20 MHz bandwidth with 0.1 uf ceramic capacitor in parallel with 10 uf electrolytic capacitor connected at the end of the output connector at nominal line
06. Turn-ON/OFF Overshoot: 5% maximum, 500uS maximum recovery time for 25% step load
07. Turn-ON Delay: 3000 mS maximum
08. Hold-Up Time: 8 mS minimum at nominal input and full load
09 Inrush Current: 30A maximum at cold start 115Vac, 60A cold start 230Vac
10. Switching Frequency: 66.5 KHz typical

B) PROTECTION
01. Over-Voltage: Protected, unit will auto recover upon removal of fault
02. Short Circuit: Protected, unit will auto recover upon removal of fault
03. Input Protection: Input line fusing

C) SAFETY
01. Dielectric Withstand Voltage: 4242Vdc from primary to secondary
02 Touch Current: <0.25mA at 240Vac
03. ROHS 2: Complies with EU 2011/65/EU and China SJ/T 11363-2006

D) OTHER:
01. MTBF: 200,000 Hours @ 25°C ambient temperature
02. Operating Temperature: 0°C to 40°C ambient temperature
03. Humidity: 0% to 90% relative humidity
04. Storage Temperature: -10°C to 80°C
05. Cooling: Convection


E) ENCLOSURE
01. Housing: High impact plastic, 94V0 polycarbonate, non-vented
02. Size: 64*40.5*29 +/-1.0 mm
03. Markings: Label and/or Pad Printed and/or Molded in the case
Derating Curve
Qty (ea.)/Carton60
Individual Box/Gift Box Size (mm)75*50*65
Individual Box/Gift Box ColorWhite
Master Carton Size (mm)420*323*179
Gross Weight (kg)12.0
Label Width (mm)33.6
Label Height (mm)25.1
Input Configuration
DescriptionBlade Options for Q Series Wall Plug-in Power SuppliesData Sheet: http://en.globtek.com/interchangeable-blades.php
Insertion Instructions: http://www.globtek.com/pdf/Instructions-Interchangeable-Blades.pdf
Video: Q-Blade Style Instruction Video




blades
User-added imageUser-added image
11                           12

INPUT CONNECTOR: Q-Socket (below are available blades configurations which are "not included" (unless stated above); can be purchased separately, package with power supply or as a separate "Q-KIT" if specified

01. United States / Canada / Japan  NEMA 1-15P configuration: NA 2 blades, Class II; US/CA/JP P/N: Q-NA(R)
02. Australian AS 3112 configuration: SAA 2 blade, Class II; AU P/N: Q-SAA(R)
03. UK BS 1363 configuration: UK 3 blade with dummy Ground, Class II; GB P/N: Q-UK(R)
04. European CEE 7/16 configuration: Europlug 2 pins, Class II; EU P/N: Q-EU(R)
05. Korean KS C8305 configuration: 2 pins, Class II; KR P/N: Q-KR(R)
06. Argentina IRAM 2073 configuration: 2 blades; AR P/N: Class II Q-AR(R)
07. China GB 2099 configuration: 2 blades, Class II; CN P/N:Q-CN(R)
08. India IS 1293 6A/SANS 164-3/BS546 configuration: 5A, 3 pins with Dummy Ground, Class II; IN P/N: Q-IN(R)
09. IEC320/C18 Inlet, Class II; P/N: Q-C18(R)
10. Brazilian NBR6147 configuration: 2 pins, Class II; BR P/N: Q-BR(R)
11. S. African SANS 164-1 configuration: 2 pins with Dummy Ground, Class II; SA P/N: Q-SANS164-1-16A(R)
12.  Israel / Malaysia / Singapore British Standard BS 546-15A configuration: 2 pins with Dummy Ground, Class II; P/N: Q-BS546-15A(R)

Kits

01. Q-KIT: 1,2,3,4 above
02. Q-KIT-INTL: 2,3,4 above
03. Q-KIT-6: 1,2,3,4,5,6 above
04. Q-KIT-7: 1,2,3,4,5,6,7 above
05. Q-KIT-8: 1,2,3,4,5,6,7,8 above

Output Configuration
Common output connector options:

L Type (Coaxial 5.5x2.5mm plug)

C Type (Coaxial 5.5x2.1mm plug)

K Type (Coaxial 3.5x1.3mm plug)

LL Type (5.5x2.5mm Locking 760k type)

CL Type (5.5x2.1mm Locking S761k type)

ML2 Type (Molex housing 43025-0200)

YL3 Type (KPPX-3P)

YL4 Type (KPPX-4P)

EJ1/2/3/4/5 (EIAJ RC-5320A type connectors)

MSB Type (Micro USB)

USBC Type (USB Type C)

Inquire for custom design

For a comprehensive list of options, click here

Contact GlobTek for your specific requirements or custom solutions.

Approvals
LogoDescription

User-added image

 
Bureau Of Indian Standards for GT-41076-0605, -0609-3.5, -0609, -0612, -0-0615, -0609-2.5, -0609-2.0, -0618, -0620, -0624 (BIS is optional, by customer note)
User-added image
R32282

Taiwan BSMI (5V designs only); http://www.bsmi.gov.tw/wSite/ct?xItem=4072&ctNode=816&mp=2
C-Tick GT-41076 N4292 SAA120084EA
C-Tick GT-41076 N4292 SAA120084EA
No Logo CB Certificate IEC 60950-1:2005 (2nd Edition), Am 1: 2009, CB report IEC 60950-1:2005 (2nd Edition), Am 1: 2009 and EN 60950-1:2006 + Am 1:2010 + Am 11:2009 + Am 12:2011
CCC Alt Less Than 2000M No Humidity
CCC to GB4943.1-2011 GB9254-2008 GB17625.1-2012
User-added image  CE Certification Class II CE Mark: tested to comply with EN55022:2006/A1:2007 Class B, EN610003-2, EN610003-3 including EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6N EN61000-4-11; EMI: Complies with EN55011 CLASS B and FCC Part 15 B
User-added image  CE Certification Class II CE Mark: tested to comply with EN 55032.2012+AC.2013 EN 61000-3-2.2014 EN 61000-3-3.2013 EN 55024.2010
User-added imageCHINA SJ/T 11364-2014, China RoHS Chart: http://en.globtek.com/globtek-rohs.php
User-added image
UL60950-1, cULus to UL 60950-1, 2nd Edition, 2007-03-27 and CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03
User-added image

Double Insulation - Mark is on the label or Molded in the case
User-added image  Certification # TC RU AR46.B.69004 Custom Union of Russia, Belarus and Kazakhstan
User-added imageIndoor Use Only - Mark is on the label or Molded in the case
IP20Ingress Protection: IP20 to IEC60529:2001 Protected against solids objects over 12mm and No Protection
User-added imageJAPAN TUV R-PSE, Cert. No. JD 50315169, to J60950-1(H26) , J55022(H22),[15V or less]. Please reference the following website for guidelines on PSE regulations: http://en.globtek.com/importing-ite-and-medical-power-supplies-ac-adaptors-to-japan/
User-added imageJAPAN TUV R-PSE, Cert. No. JD 50315866, to J60950-1(H26) , J55022(H22),[DC15V≤30V]. Please reference the following website for guidelines on PSE regulations: http://en.globtek.com/importing-ite-and-medical-power-supplies-ac-adaptors-to-japan/
User-added image
Korea KET KC Mark GT-41076-0605 HU10150-8012A (5V Only)
 User-added image

Efficiency: complies to section 301 of Energy Independence and Security Act (EISA) complies with Energy Star tier 2 (North America), ECP tier 2 (China), MEPS tier 2 (Australia), Code of Conduct (Europe)
LPSLimited Power Source
User-added imageEEV1191Natural Resources Canada (NRCan): CSA Standard C381.1-08, QSP NRCAN EEV1191; http://shop.csa.ca/en/canada/energy-efficiency/cancsa-c3811-08/invt/27024802008
User-added imageJAPAN TUV Rheinland-PSE GlobTek Inc to J60950-1(H26) , J55022(H22),J3000(H25).Please follow the procedure listed in the following link for proper import to Japan: http://en.globtek.com/importing-to-japan.php.
RoHS 2RoHS 2: Complies with EU 2011/65/EU and CHINA SJ/T 11363-2006 http://www.ce-mark.com/Rohs%20final.pdf
User-added image
IEC/EN60950-1
SIQ Mark License EN60950-1
User-added imageUkraine UKRSepro (Document: www.globtek.com/html/iso_certificates/GT_Ukraine.pdf)
User-added imageJapan: Voluntary Control Council for Interference (VCCI)
 User-added imageWEEE: Complies with EU 2012/19/EU (http://ec.europa.eu/environment/waste/weee/index_en.htm) Mark is on the label or Molded in the case
Popular Products
SKUVolts OutCurrent Out (Amps)Connector
137741100.6Telephone Plug 4P4C (Handset Connector)
161807120.52 Pin DC Jack
100414120.5Female Barrel 5.5*2.5*11mm, Right Angle without internal Spring Clip & Locking Notch or Equal
149066120.5Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
225596120.5Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
137677120.5Socket for interchangeable o/p connectors
137676120.5Female Barrel 5.5*2.5*11mm, Right Angle without internal Spring Clip & Locking Notch or Equal
101409120.52 Pin DC Jack
117868120.52 Pin DC Jack
124167120.5Female Barrel 5.5 * 2.5 * 11mm with internal Spring Clip and Locking Notch or Equal
171300120.5Female Barrel Right Angle, 5.5*2.1*9.5mm with internal Spring Clip and Locking Notch or Equal
137674120.5Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
137675120.5Female Barrel 5.5 * 2.5 * 11mm with internal Spring Clip and Locking Notch or Equal
100388130.46Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
124133150.4Female Barrel Right Angle, 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
161885150.4Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
149114150.4Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
137707180.333Female Barrel 5.5 * 2.5 * 11mm with internal Spring Clip and Locking Notch or Equal
100582240.25Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
137719240.25Socket for interchangeable o/p connectors
168593240.25Split 3in ( 76.2mm); Strip 0.25in (6.35mm) or Equal
1671313.51.02 Pin FX9
1657313.51.02 Pin F2J, DC Jack or Equal
17511140.5Female Barrel straight 3.5*1.3*9.5mm, without Locking Notch nor Spring Clip or Equal
17072541Female Barrel 5.5*2.1*11mm w/ Spring Clip & Locking Notch or Equal
17099540.5Female Barrel 5.5*2.1*11mm w/ Spring Clip & Locking Notch or Equal
17511040.5Female Barrel straight 3.5*1.3*9.5mm, without Locking Notch nor Spring Clip or Equal
1276654.11.2Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
10171551.2Micro-B USB 5 Pin Type "B" or Equal
10188551.2Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
12414451.2Type "A" USB 4 Pin Jack or Equal
12766351.2Stripped 30 +/-10mm; Tinned 9 +/- 2mm
12767151.2Female Barrel, Right Angle 3.5 * 1.35 * 9.5, No internal Spring Clip and Locking Notch or Equal
12767451.2Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
12767851.2Female Barrel, Locking, 5.5 * 2.5 * 13.8mm w/ 4.0mm Thumb Screw or Equal
12767951.2Female Barrel 5.5*2.5*11mm, Right Angle without internal Spring Clip & Locking Notch or Equal
13753451.2Female Barrel 3.5*1.35*9.5mm, with Locking Notch and Spring Clip or Equal
13753551.2Female Barrel 3.5*1.35*9.5mm, with Locking Notch and Spring Clip or Equal
13753851.2M12 Female straight connector with self-locking threaded joint, equivalent or LUMBERG p/n:RKC 4/7, 4pinR
13754051.2Mini-B USB 5 Pin Type "B" or Equal with 200 Ohm resistor between Pin 2 & 3
13754551.2Micro-B USB 5 Pin Type "B" or Equal
13754651.2Socket for interchangeable o/p connectors
14877351.2Mini-B USB 5 Pin Type "B" or Equal with 200 Ohm resistor between Pin 2 & 3
16405951.2Female Barrel 3.5*1.35*9.5mm, with Locking Notch and Spring Clip or Equal
16571951Mini-B USB 5 Pin Type "B" or Equal
16573251.2M12 Female straight connector with self-locking threaded joint, equivalent or LUMBERG p/n:RKC 4/7, 4pinR
16812651.2Female Barrel 5.5*2.1*9.5mm No internal Spring Clip nor Locking Notch or Equal
16887751.2Female Barrel 5.5*2.1*11mm w/ Spring Clip & Locking Notch or Equal
17524151.2Micro-B USB 5 Pin Type "B" or Equal
17780451.2Stripped 30 +/-5mm; Tinned 9 +/- 2mm or Equal
19771051.2Micro-B USB 5 Pin Type "B" or Equal
19937951.2Female Barrel 4.75*1.7*9.5mm or Equal
18077251.2Mini-B USB 5 Pin Type "B" or Equal with 200 Ohm resistor between Pin 2 & 3
18252851.2Micro-B USB 5 Pin Type "B" or Equal
20182451.2TE Connectivity 4 Pin IDC Connector MTA100 22AWG RED, p/n 3-640440-4
26162651Female Barrel 3.5*1.35*9.0 mm, with Internal Spring Clip and Locking Notch or Equal
1375295.51.09Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
17132561Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
16702461Female Barrel 4.75*1.7*9.5mm or Equal
16576161Female Barrel 4.75*1.7*9.5mm or Equal
12769961Female Barrel 3.5*1.35*9.0 mm, with Internal Spring Clip and Locking Notch or Equal
14886461.0Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
11757361Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
19918561Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
16320261Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
1175806.50.92Male Plug KCC, MFG P/N: 16290
18593590.66None
13763790.66Female Barrel Right Angle, 5.5*2.1*9.5mm with internal Spring Clip and Locking Notch or Equal
13763390.66Socket for interchangeable o/p connectors
11773290.66AFemale Barrel 3.5*1.3*11mm, No internal Spring Clip nor Locking Notch or Equal
11772790.5MOLEX P/N:43025-0800 Micro-fit 3.0 (8) circuit connector housing with MOLEX TERMINAL P/N: 430303-0080 Female terminal or Equal
10792190.66Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
14397690.66Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
18154390.66Female Barrel 3.5*1.35*9.5mm, with Locking Notch and Spring Clip or Equal
18431290.66CONN PIN SPRING-LOAD .217 20GOLD
1814619.50.63Female Barrel 5.5*2.1*12mm No internal Spring Clip nor Locking Notch or Equal
10188551.2Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
10188551.2Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
13754051.2Mini-B USB 5 Pin Type "B" or Equal with 200 Ohm resistor between Pin 2 & 3
14877351.2Mini-B USB 5 Pin Type "B" or Equal with 200 Ohm resistor between Pin 2 & 3
13754051.2Mini-B USB 5 Pin Type "B" or Equal with 200 Ohm resistor between Pin 2 & 3
14877351.2Mini-B USB 5 Pin Type "B" or Equal with 200 Ohm resistor between Pin 2 & 3
14877351.2Mini-B USB 5 Pin Type "B" or Equal with 200 Ohm resistor between Pin 2 & 3
13754051.2Mini-B USB 5 Pin Type "B" or Equal with 200 Ohm resistor between Pin 2 & 3
News Releases
TitleWeb Link
Flexible LED Strip Light cable assembly in Warm white 3200k for industrial lighting application available in stock and modified configurations, model LMPWHLED250MMX3(R)http://en.globtek.com/news.php/flexible-led-strip-light-cable-assembly-in-warm-white-3200k-for-industrial-lighting-application-available-in-stock-and-modified-configurations-model-lmpwhled250mmx3r-2#.Uq9ASfRDv74

Request Info