Request Information Download PDF Configure Output Connector
GT-41081-WWVV-X.X-Q GT-41081-WWVV-X.X-Q
Information
Model NumberGT-41081-WWVV-X.X-Q
DescriptionGT-41081-WWVV-X.X-Q, ITE Power Supply, Wall Plug-in, Regulated Switchmode AC-DC, , Input Rating: 100-240V~, 50-60 Hz, Blade Options for Q Series Wall Plug-in Power Supplies, Output Rating: 18 Watts, 5-9V in 0.1V increments, Approvals: VCCI CCC PSE Ukraine GOST-R Level V NrCAN C-Tick LPS RoHS 2 EC Double Insulation WEEE China RoHS CB IP52 NEMKO UL/cUL PSE PSE Korea
Agency Documentshttp://www.globtek.info/certs/GT-41081/
CE EC-Declaration for MedicalContact GlobTek for more information
CE EC-Declaration for Industrial/Commercial/ITEhttp://globtek.force.com/models/ec_declaration?id=a0O30000007P7YQEA0
RoHS/RoHS2 Declarationhttp://www.globtek.com/pdf/rohs_cert/a0O30000007P7YQEA0
REACH Declarationhttp://www.globtek.com/pdf/iso_certificates/REACH.pdf
Conflict Minerals Declarationhttp://www.globtek.com/pdf/conflict-minerals.pdf
Model Parameters
TypeWall Plug-in
TechnologyRegulated Switchmode AC-DC
CategoryITE Power Supply
Input Voltage100-240V~, 50-60 Hz
I/P Amps (A)0.6 A
Wattage (W)18
Vout Range (V)5-9
EfficiencyV
Ingress ProtectionIP52
Size (mm)43.5 x 74.0 x 35.3
EnclosureUser-added image


 
Rating Table
Model Number VoltageAmps (A)Watts (W) RFQ
GT-41081-1505 52.613 RFQ
GT-41081-1805 5315 RFQ
GT-41081-1806-0.8 5.2315.6 RFQ
GT-41081-1806 6318 RFQ
GT-41081-1506 62.515 RFQ
GT-41081-1809-2.5 6.52.7617.94 RFQ
GT-41081-1809-1.5 7.52.418 RFQ
GT-41081-1509 91.715.3 RFQ
GT-41081-1809 9218 RFQ
SpecificationsA) ELECTRICAL SPECIFICATIONS:
01. Input Voltage: Specified 90-264 Vac, Nameplate rated: 100-240Vac
02. Input Frequency: Specified 47-63 Hz, Nameplate rated 50-60Hz
03. Output Regulation: +/- 5% measured at the output connector
04. Line Voltage Regulation: +/- 1% typical measured at the output connector
05. Output Ripple (Vp-p): +/-1% or 150 mV whichever is greater, measured at 20 MHz bandwidth with 0.1 uf ceramic capacitor in parallel with 10 uf electrolytic capacitor connected at the end of the output connector at nominal line
06. Turn-ON/OFF Overshoot: 5% maximum, 1 mS typical recovery time for 25% to 50% step load
07. Turn-ON Delay: 1 second typical
08. Hold-Up Time: 8 mS typical @ nominal input voltage and full load
09. Inrush Current: 30A typical at 115VAC input and 60A typical at 230 VAC input
10. Switching Frequency: 65 KHz typical

B) PROTECTION
01. Over-Voltage: Protected Zener clamp across the output
02. Short Circuit: Protected unit will auto recover upon removal of fault
03. Input Protection: Input line fusing

C) SAFETY
01. Dielectric Withstand Voltage: 4242Vdc from primary to secondary
02. Touch Current: <0.25mA @ 240Vac input voltage
03. ROHS 2: Complies with EU 2011/65/EU and GB/T26572-2011

D) OTHER:
01. MTBF: 200,000 Hours @ 25°C ambient temperature
02. Operating Temperature: 0°C to 40°C ambient temperature
03. Humidity: 0% to 90% relative humidity
04. Storage Temperature: -10°C to 80°C
05. Cooling: Convection

E) ENCLOSURE
01. Housing: High impact plastic, 94V0 polycarbonate, non-vented
02. Size: 43.5 x 74.0 x 35.3 +/-1.0mm
03. Markings: Label and/or Pad Printed and/or Molded in the case
Derating Curve
Qty (ea.)/Carton80
Individual Box/Gift Box Size (mm)90.5*73*53
Individual Box/Gift Box ColorWhite
Master Carton Size (mm)388 x 380 x 245
Gross Weight (kg)15.2
Label Width (mm)29.8
Label Height (mm)20.8
Input Configuration
DescriptionBlade Options for Q Series Wall Plug-in Power SuppliesData Sheet: http://en.globtek.com/interchangeable-blades.php
Insertion Instructions: http://www.globtek.com/pdf/Instructions-Interchangeable-Blades.pdf
Video: Q-Blade Style Instruction Video




blades
User-added imageUser-added image
11                           12

INPUT CONNECTOR: Q-Socket (below are available blades configurations which are "not included" (unless stated above); can be purchased separately, package with power supply or as a separate "Q-KIT" if specified

01. United States / Canada / Japan  NEMA 1-15P configuration: NA 2 blades, Class II; US/CA/JP P/N: Q-NA(R)
02. Australian AS 3112 configuration: SAA 2 blade, Class II; AU P/N: Q-SAA(R)
03. UK BS 1363 configuration: UK 3 blade with dummy Ground, Class II; GB P/N: Q-UK(R)
04. European CEE 7/16 configuration: Europlug 2 pins, Class II; EU P/N: Q-EU(R)
05. Korean KS C8305 configuration: 2 pins, Class II; KR P/N: Q-KR(R)
06. Argentina IRAM 2073 configuration: 2 blades; AR P/N: Class II Q-AR(R)
07. China GB 2099 configuration: 2 blades, Class II; CN P/N:Q-CN(R)
08. India IS 1293 6A/SANS 164-3/BS546 configuration: 5A, 3 pins with Dummy Ground, Class II; IN P/N: Q-IN(R)
09. IEC320/C18 Inlet, Class II; P/N: Q-C18(R)
10. Brazilian NBR6147 configuration: 2 pins, Class II; BR P/N: Q-BR(R)
11. S. African SANS 164-1 configuration: 2 pins with Dummy Ground, Class II; SA P/N: Q-SANS164-1-16A(R)
12.  Israel / Malaysia / Singapore British Standard BS 546-15A configuration: 2 pins with Dummy Ground, Class II; P/N: Q-BS546-15A(R)

Kits

01. Q-KIT: 1,2,3,4 above
02. Q-KIT-INTL: 2,3,4 above
03. Q-KIT-6: 1,2,3,4,5,6 above
04. Q-KIT-7: 1,2,3,4,5,6,7 above
05. Q-KIT-8: 1,2,3,4,5,6,7,8 above

Output Configuration
Common output connector options:
Click to add to your request.






L Type (Coaxial 5.5x2.5mm plug) C Type (Coaxial 5.5x2.1mm plug) K Type (Coaxial 3.5x1.3mm plug) LL Type (5.5x2.5mm Locking 760k type) CL Type (5.5x2.1mm Locking S761k type) Magnetic Connector





YL3 Type (KPPX-3P) YL4 Type (KPPX-4P) EJ1/2/3/4/5 (EIAJ RC-5320A type connectors) MSB Type (Micro USB) Inquire for custom design

For a comprehensive list of options, click here

Contact GlobTek for your specific requirements or custom solutions.

Approvals
LogoDescription
C-Tick GT-41081 N18647 WT 11105824-S-E-O
C-Tick GT-41081 N18647 WT 11105824-S-E-O
No Logo CB Certificate IEC 60950-1:2005 (2nd Edition), Am 1: 2009, CB report IEC 60950-1:2005 (2nd Edition), Am 1: 2009 and EN 60950-1:2006 + Am 1:2010 + Am 11:2009 + Am 12:2011
User-added imageCCC to GB4943.1-2011 GB9254-2008 GB17625.1-2012, Tropical <2000
User-added imageCHINA SJ/T 11364-2014, China RoHS Chart: http://en.globtek.com/globtek-rohs.php
User-added imageUL60950-1, cULus to UL 60950-1, 2nd Edition, 2007-03-27 and CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03
User-added image

Double Insulation - Mark is on the label or Molded in the case
No LogoEC-Conformity Declaration: http://www.globtek.com/html/iso_certificates/EC-DECLARATION.pdf, REACH 144 SVHC: http://www.globtek.com/html/iso_certificates/Reach144.pdf
User-added image
 
GOST-R mark for Russia(Document: http://www.globtek.com/html/iso_certificates/GT_GOST-R.pdf). 03/15/2015. Due to lack of demand, GlobTek will not be renewing it's GOST certification. Please contact your sales engineer for pricing on EAC.
User-added imageIndoor Use Only - Mark is on the label or Molded in the case
IP52Ingress Protection: IP52 to IEC60529:2001 Protected against dust - limited ingress (no harmful deposit) and Protected against direct sprays up to 15 degrees from the vertical
User-added imageJAPAN TUV R-PSE, Cert. No. JD 50313285, to J60950-1(H26) , J55022(H22),J3000(H25)[15V or less]. Please reference the following website for guidelines on PSE regulations: http://en.globtek.com/importing-ite-and-medical-power-supplies-ac-adaptors-to-japan/
User-added imageJAPAN TUV R-PSE, Cert. No. JD 50314327, to J60950-1(H26) , J55022(H22),J3000(H25)[15V or less]. Please reference the following website for guidelines on PSE regulations: http://en.globtek.com/importing-ite-and-medical-power-supplies-ac-adaptors-to-japan/
User-added image


 
Korea KET KC Mark GT-41081-1505 HU10499-15023A (5V Only)
 User-added image

Efficiency: complies to section 301 of Energy Independence and Security Act (EISA) complies with Energy Star tier 2 (North America), ECP tier 2 (China), MEPS tier 2 (Australia), Code of Conduct (Europe)
LPSLimited Power Source
User-added imageNEMKO EN60950-1:2006, A11, A1, A12,A2
User-added imageEEV1191Natural Resources Canada (NRCan): CSA Standard C381.1-08, QSP NRCAN EEV1191; http://shop.csa.ca/en/canada/energy-efficiency/cancsa-c3811-08/invt/27024802008
User-added imageJAPAN TUV Rheinland-PSE GlobTek Inc to J60950-1(H26) , J55022(H22),J3000(H25).Please follow the procedure listed in the following link for proper import to Japan: http://en.globtek.com/importing-to-japan.php.
RoHS 2RoHS 2: Complies with EU 2011/65/EU and CHINA SJ/T 11363-2006 http://www.ce-mark.com/Rohs%20final.pdf
User-added imageUkraine UKRSepro (Document: www.globtek.com/html/iso_certificates/GT_Ukraine.pdf)
User-added imageJapan: Voluntary Control Council for Interference (VCCI)
 User-added imageWEEE: Complies with EU 2012/19/EU (http://ec.europa.eu/environment/waste/weee/index_en.htm) Mark is on the label or Molded in the case
Popular Products
SKUVolts OutCurrent Out (Amps)Connector
13755852.6Stripped 50 +/-5mm; Tinned 9 +/- 2mm or Equal
18410853.0Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
18646353.02x SX0L0C-P09MCC0-0001 ODU MINI-SNAP size 0 Plug and 700.022.208.960.040 cable strain relief (one each) NO Equivalent
13757253Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
13757353Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
13757653Socket for interchangeable o/p connectors
13757953.0Female Barrel 4.0*1.7*9.5mm Right angle with internal Spring Clip and Locking Notch or Equal
10655353Female Barrel 5.5 * 2.1 * 13.8 mm w/ 4 mm Thumb Screw or Equal
14367553Female Barrel 5.5 * 2.5 * 11mm with internal Spring Clip and Locking Notch or Equal
14883253Female Barrel Right Angle, 5.5*2.1*11mm with internal Spring Clip and Locking Notch or Equal
14945653Female Barrel 3.5*1.35*9.5mm, without Locking Notch nor Spring Clip or Equal
14959553Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
18716753.0Outer Jacket Stripped 7 +/- 3mm and Wire Stripped & Tinned 2.8 - 4mm NO equivalent
165883533 Pin Kycon KPP-3 Locking Plug or Equal
16690053Female Barrel 5.5 * 2.1 * 13.8 mm w/ 4 mm Thumb Screw or Equal
16707253FEMALE BARREL 5.5*2.5*9.5 mm SHOGYO P/N: SCDP443DBNNNBPTG OR EQUIVALENT
16742753Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
16983052Female Barrel 4.75*1.7*9.5mm or Equal
17071452.6Stripped 50 +/-5mm; Tinned 9 +/- 2mm or Equal
17076153Female Barrel 5.5 * 2.1 * 13.8 mm w/ 4 mm Thumb Screw or Equal
20122553Female Barrel Right Angle, 5.5*2.1*11mm with internal Spring Clip and Locking Notch or Equal
17087752.6Stripped 50 +/-5mm; Tinned 9 +/- 2mm or Equal
17322252Female Barrel Right Angle, 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
17510653Female Barrel 3.5*1.35*9.5mm, without Locking Notch nor Spring Clip or Equal
17550753Female Barrel 3.5*1.35*7.5mm, without Locking Notch nor Spring Clip or Equal
26339553.0Outer Jacket Stripped 7 +/- 3mm and Wire Stripped & Tinned 2.8 - 4mm NO equivalent
1769585310 pins plug connector
21381953Female Barrel, Locking, 5.5 * 2.5 * 13.8mm w/ 4.0mm Thumb Screw or Equal
19626753Female Barrel 5.5*2.1*9.5mm with internal Spring Clip and Locking Notch or Equal
20959553Female Barrel, Locking, 5.5 * 2.5 * 13.8mm w/ 4.0mm Thumb Screw or Equal
19805953.0Outer Jacket Stripped 7 +/- 3mm and Wire Stripped & Tinned 2.8 - 4mm NO equivalent
17932853Micro USB type B without resistor
17933053Micro USB type B without resistor
24670953Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
18036653Female Barrel, Right Angle 3.5 * 1.35 * 9.5mm with internal Spring Clip and Locking Notch or Equal
18086253FEMALE BARREL 5.5*2.5*9.5 mm SHOGYO P/N: SCDP443DBNNNBPTG OR EQUIVALENT
18098253Female Barrel 3.5*1.3*9.5 mm, with Locking Notch and Spring Clip or Equal
18108853Female Barrel straight 3.5*1.3*9.5mm, without Locking Notch nor Spring Clip or Equal
18151553Type "A" USB 4 Pin Jack or Equal
18381153Socket for interchangeable o/p connectors
2382875.23Micro-B USB 5 Pin Type "B" or Equal
18788163Female Barrel 3.8*1.35*8mm No internal Spring Clip nor Locking Notch or Equal
18027863Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
13759163Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
17551663Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
1708446.32.38Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
2295016.52.76Circular 2P(5A)
1980586.52.76Circular 2P(5A)
1961657.52.4Female Barrel 5.5*2.1*12.5mm w/Spring Clip and Locking Notch or Equal
1657777.52.4Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
1176587.52.4Female Barrel 3.5*1.35*11mm, with Locking Notch and Spring Clip or Equal

Request Info