EIAJ RC-5320A Connectors in type 1,2,3,4 and 5 Available in molded and changeable configurations for AC to DC Adapters, DC to DC adapters, and Cable assemblies
EIAJ RC-5320A Connectors are popular low voltage connectors used on AC to DC power supplies and adapters or used on cable assemblies.
The design philosophy is that higher voltages should be supplied via larger plugs to prevent equipment damage. A larger plug will not go into a smaller jack.
An overview of EIAJ RC-5320A Connectors is below. GlobTek offers all options both as overmolded plugs for power adapters or on cable assemblies. GlobTek also offer's it's T00 changeable output connector system on most common output voltages and current combination power adapters and also common cable assembly lengths which are widely stocked for immediate needs.
These plugs may be overmolded on various types of cables, both round and flat, in a number of guages and can be made in any length with any termination on the opposite end.
|Connector Name||Minimum Voltage||Rated Voltage||Rated Current||Outer Diameter||Inner Diameter||Pin Diameter||Shaft Length|
|EIAJ-01||0 V||3.15 V||2 A||plug: 2.35 mm|
jack: 2.75 mm hole
|plug: 0.7 mm|
jack: 0.65 mm pin
|EIAJ-02||3.15 V||6.3 V||2 A||plug: 4.0 mm|
jack: 4.4 mm hole
|plug: 1.7 mm|
jack: 1.65 mm pin
|EIAJ-03||6.3 V||10.5 V||2 A||plug: 4.75 mm|
jack: 5.15 mm hole
|plug: 1.7 mm|
jack: 1.65 mm pin
|EIAJ-04||10.5 V||13.5 V||2 A||5.5 mm||3.4 mm||1.0 mm||9.5~13.5 mm|
|EIAJ-05||13.5 V||18.0 V||2 A||6.5 mm||4.4 mm||1.4 mm||9.5~16 mm|
GlobTek is a power systems solutions provider with design and manufacturing facilities in the USA and China and sales offices in Germany, France, and the UK. Offering a line of power supplies and cable assemblies for applications from gym equipment to medical systems, GlobTek can also develop and create custom power solutions for just about any application. GlobTek is located at 186 Veterans Drive, Northvale NJ 07647. For more information call 201-784-1000 or visit GlobTek online at www.globtek.com.
Made in USA option available.
5 year warranty
Quick reference for common terms used in reference to Power Supply Cords
AWG Abbreviation for American Wire Gauge.
Alternating Current (A-C) The charge flow of a current periodically and regularly reverses in a cyclic manner.
Ampere (A) Unit that expresses rate of flow of an electrical current. One ampere is the current flowing through one OHM of resistance at one volt potential.
CEE International Color Code. See Inner Conductor Colors.
CSA Canadian Standards Association. This is a nonprofit, independent organization that operates a listing service for electrical materials and equipment in the Canadian counterpart of the Underwriters Laboratories.
HPN Parallel Heater Cord, typically Neoprene-insulated two conductor.
Hypot A test designed to determine the highest potential that can be applied to a conductor without breaking through the insulation.
ICC International Color Code on the inner conductors (blue, brown, green with yellow stripe). See Inner Conductor Colors.
IEC International Electromechanical Commission. A European group consisting of multi-national representatives which develop standards for electrical components. See IEC-320 Standardized Appliance Connectors.
Inner Conductor Colors
|Function||North American (NA)||International (ICC)|
|Earth (Ground)||Green||Green w/yellow stripe|
Insulated Wire A conductor of electricity covered with a nonconducting material.
Jacket An extruded layer of insulation over a wire or group of cables.
Kilowatt (kW) A unit of power equal to one thousand watts.
Line Cord A cord, terminating in a plug at one end, used to connect equipment or appliances to a power unit.
N.A. North American color code on the inner conductors (black, white, green). See Inner Conductor Colors.
National Electrical Manufacturers Association (NEMA) Standard of wire, plug and cable specifications. See NEMA Plug & Receptical Configurations.
OD Abbreviation for outside diameter.
OHM Unit of electrical resistance. Resistance of a circuit in which a potential difference of one volt produces a current of one ampere.
PVC Polyvinyl chloride Compound used in thermoplastic SVT, SJT.
Power Supply Cord An attachment plug molded to a length of flexible cord. May also include a molded on strain relief, or terminations on the end opposite the plug.
Rated Voltage The maximum voltage at which an electric component can operate for extended periods without undo degradation or safety hazard.
Receptacle A contact device installed at the outlet for the connection of a single attachment plug.
Ribbed Outer jacket is striated with ribs.
Rip Cord Two or more insulated conductors in a parallel configuration which may be easily separated leaving the insulation of each conductor intact.
S Designated for heavy duty, rubber insulated portable cord. Stranded copper conductors with separator and individual rubber insulation. Two or more color coded conductors cabled with filler, wrapped with separator and rubber jacketed overall, 600V.
SEOW-A Extra hard service cord. Thermoplastic elastomer, oil resistant (TPE) construction Jacket. 600 volt, weather resistant for outdoor use.
SJ Designated for junior hard service, rubber insulated pendant or portable cord. Same construction as type S, but 300V.
SJEOW-A Extra hard service cord. Thermoplastic elastomer, oil resistant (TPE) construction jacket. 300 volt, weather resistant for outdoor use.
SJ0 Same as SJ but neoprene, oil resistant compound out jacket, 300V, 600C.
SJT Designated for junior hard service thermoplastic or rubber insulated conductors with overall thermoplastic outer jacket, 300V, 600C.
SJTO Same as SJT but oil resistant thermoplastic outer jacket.
SJTW A hard service cord. Thermoplastic constructed jacket. 300 volt, weather resistant for outdoor use.
S0 Designated for a 600 Volt senior service, oil resistant neoprene jacket cord. Same construction as type S except for neoprene jacket.
S0-W Heavy duty type 50-dual rated type W
SPT-1 Thermoplastic constructed, parallel jacketed, 300 volt, 2 or 3 conductor, 18 gauge.
SPT-2 Same as SPT-1 but heavier construction. 18-16 gauge.
SPT-3 Same as SPT-2 but heavier construction. 18-10 gauge.
ST Hard service cord, jacketed same as type S except all plastic construction, 600V 600 to 1050C.
STO Same as ST but with oil resistant thermoplastic outer jacket, 600V.
STW-A Extra hard service cord. Thermoplastic constructed jacket. 600 volt, weather resistant for outdoor use.
SV Designated for vacuum cleaner cord, two-or-three conductor, rubber insulated. Overall rubber jacket. For light duty in damp location. 300V, 600C.
SVT Same as SV except all plastic construction. With or without third conductor for grounding purposes only. 300V, 600-900C.
Shielded-Type Cable A cable in which the conductors are enclosed in a conducting envelope constructed so that substantially every point on the surface of the insulation is at ground potential or at some predetermined potential with respect to ground under normal operating conditions.
Strip To remove insulation from a cable.
Temperature Rating The maximum temperature at which the insulating material may be used in continuous operation without loss of its basic properties.
Terminal Any device attached to the conductor by crimping, soldering or welding.
Tensile Strength The pulling stress required to break a given specimen.
Thermoplastic Elastomer (TPE) A jacketed material which has many of the characteristics of rubber, as well as excellent electrical, mechanical and chemical properties.
Thermosetting A classification of resin which cures by chemical reaction when heated and, when cured, can not be resoftened by heating.
Tinned A silver-white, ductile metal used to coat copper conductors, especially when solder termination is to be used.
Tolerance The acceptable deviation from specification.
UL Underwriters Laboratories. This is a nonprofit independent organization that operates a listing service for electrical and electronic materials and equipment.
VW-1 A flammability rating established by Underwriters Laboratories for wires and cables that pass a specially designed vertical flame test, formerly designated FR-1.
Volt (V) Unit of electromotive force. It is the difference of potential required to make a current of one ampere flow through a resistance of one OHM.
Voltage The term most often used in place of electromotive force, potential, difference or voltage drop, to designate electric pressure that exists between two points and is capable of producing a flow of current when a closed circuit is connected between the two points.
Voltage Breakdown Test to determine maximum voltage of insulated wire before electrical current leakage through insulation. See hypot.
Voltage Rating The highest point that may be continuously applied to a wire or cord in conformance with standards or specifications.
W-A UL designation for outdoor-approved flexible cord.
Watt (W) Unit of power or work done at the rate of one joule per second or rate of work represented by current of one ampere under a pressure of one volt (volt-ampere).
Wire Gauge A system of numerical designations of wire sizes.