Regulated Switchmode AC-DC Power Supply AC Adaptor
Category
ICT/ITE Power Supply
Input Voltage Range (V)
100-240V~, 50-60 Hz
Max Input Current (A)
0.6A
Max Output Power Rating (W)
18
Output Voltage Range (V)
9-48
Efficiency
V
Ingress Protection
IP52
Size (mm)
43.5*74*35.3
Enclosure
Rating Table
Model Number (Final ordering #/Part No to be defined)
Voltage
Amps (A)
Watts (W)
RFQ
GT-41080-1617.9-8.9*
GT-41080-1624-6.0*
GT-41080-1817.9-5.9*
GT-41080-1624*
GT-41080-1617.9-2.9*
GT-41080-1624-4.0*
GT-41080-1807*
7
2.57
17.99
GT-41080-1817.9-8.9*
9
2
18
GT-41080-1817.9-7.1*
10.8
1.66
17.93
GT-41080-1811*
11
1.67
18.37
GT-41080-1817.9-5.9*
12
1.5
18
GT-41080-1217.9-5.9*
12
1
12
GT-41080-1817.9-2.9*
15
1.2
18
GT-41080-1817.9*
17.9
1
17.9
GT-41080-1824-6.0*
18
1
18
GT-41080-1824-4.0*
20
0.9
18
GT-41080-1824*
24
0.75
18
GT-41080-1830*
30
0.6
18
GT-41080-1838*
38
0.47
17.86
GT-41080-1848*
48
0.375
18
* (Final ordering #/Part No to be defined)
Specifications
A) ELECTRICAL SPECIFICATIONS:
01. Input Voltage: Specified 90-264 Vac, Nameplate rated: 100-240Vac
02. Input Frequency: Specified 47-63 Hz, Nameplate rated 50-60Hz
03. Line Voltage Regulation: +/- 1% typical measured at the output connector
04. Output load regulation : +/- 5% measured at O/P connector
05. Output Ripple (Vp-p): +/-1% or 150 mV whichever is greater, measured at 20 MHz bandwidth with 0.1 uf ceramic capacitor in parallel with 10 uf electrolytic capacitor connected at the end of the output connector at nominal line
06. Turn-ON/OFF Overshoot: 5% maximum, 1 mS typical recovery time for 25% to 50% step load
07. Turn-ON Delay: 1 second typical
08. Hold-Up Time: 8 mS typical @ nominal input voltage and full load
09. Inrush Current: 30A typical at 115VAC input and 60A typical at 230 VAC input
10. Switching Frequency: 65 KHz typical
B) PROTECTION
01. Over-Voltage: Protected Zener clamp across the output
02. Short Circuit: Protected unit will auto recover upon removal of fault
03. Input Protection: Input line fusing
C) SAFETY
01. Dielectric Withstand Voltage: 4242Vdc from primary to secondary
02. Touch Current: <0.25mA @ 240Vac input voltage
03. ROHS 2: Complies with EU 2011/65/EU and China SJ/T 11363-2006
D) OTHER:
01. MTBF: 200,000 Hours @ 25°C ambient temperature
02. Operating Temperature: 0°C to 40°C ambient temperature
03. Humidity: 0% to 90% relative humidity
04. Storage Temperature: -10°C to 80°C
05. Cooling: Convection
E) ENCLOSURE
01. Housing: High impact plastic, 94V0 polycarbonate, non-vented
02. Size: 43.5 x 74.0 x 35.3 +/-1.0 mm
03. Markings: Label and/or Pad Printed and/or Molded in the case
INPUT CONNECTOR: Q-Socket (below are available blades configurations which are "not included" (unless stated above); can be purchased separately, package with power supply or as a separate "Q-KIT" if specified
01. United States / Canada / Japan NEMA 1-15P/ IEC PLUG Type A [WORKS IN PLUG B] configuration: NA 2 blades, Class II; US/CA/JP P/N: Q-NA(R) 02. Australian AS 3112 configuration: SAA 2 blade/ IEC TYPE I, Class II; AU P/N: Q-SAA(R) 03. UK BS 1363 configuration: UK 3 blade with dummy Ground/ IEC TYPE G, Class II; GB P/N: Q-UK(R) 04. European CEE 7/16 configuration: Europlug 2 pins/ IEC TYPE C [WORKS IN TYPE E&F], Class II; EU P/N: Q-EU(R) 05. Korean KS C8305 configuration: 2 pins/SIMILAR TO IEC TYPE C, Class II; KR P/N: Q-KR(R) 06. Argentina IRAM 2073 configuration: 2 blades/SIMILAR TO IEC TYPE I; AR P/N: Class II Q-AR(R) 07. China GB 2099 configuration: 2 blades/SIMILAR TO TYPE A, Class II; CN P/N:Q-CN(R) 08. India IS 1293 6A/BS546 configuration: 5A, 3 pins with Dummy Ground, Class II/IEC TYPE D; IN P/N: Q-IN(R) 09. IEC60320/C18 Inlet, Class II; P/N:Q-C18(R) 10. Brazilian NBR6147 configuration: 2 pins, Class II;SIMILAR TO IEC TYPE C BR P/N: Q-BR(R) 11. South Africa SABS164-1, 3 round prongs, Class II + dummy ground, IEC TYPE M P/N: Q-SANS164-1-16A(R) 12. South Africa SABS164-4, 3 round prongs with a notched prong @ 0º, Class II + dummy ground, IEC TYPE M Red, P/N: Q-SANS164-4L-16A(R) 13. South Africa SABS164-4, 3 round prongs with a notched prong @ -53º, Class II + dummy ground, Blue, IEC TYPE M, P/N: Q-SANS164-4C-16A(R) 14. South Africa SABS164-4, 3 round prongs with a notched prong @ +53º, Class II + dummy ground, Black,IEC TYPE M P/N: Q-SANS164-4R-16A(R)
CB Certificate IEC 60950-1:2005 (2nd Edition), Am 1: 2009, CB report IEC 60950-1:2005 (2nd Edition), Am 1: 2009 and EN 60950-1:2006 + Am 1:2010 + Am 11:2009 + Am 12:2011
CE Mark: tested to comply with EN55022:2006/A1:2007 Class B, EN610003-2, EN610003-3 including EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6N EN61000-4-11; EMI: Complies with EN55011 CLASS B and FCC Part 15B - On label or Molded in case
CHINA SJ/T 11364-2014, China RoHS Chart: http://en.globtek.com/globtek-rohs.php
UL60950-1, cULus to UL 60950-1, 2nd Edition, 2007-03-27 and CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03
Certification # TC RU AR46.B.75423 Custom Union of Russia, Belarus and Kazakhstan
Compliance of this power supply with FCC Part 15, Class B has been demonstrated with a standard output load. The FCC law stipulates that system-level testing is required to demonstrate compliance with the FCC emission limits with the actual system load.
Indoor Use Only - Mark is on the label or Molded in the case
IP52
Ingress Protection: ?IP52 to IEC60529:2001 Protected against dust - limited ingress (no harmful deposit) and Protected against direct sprays up to 15 degrees from the vertical
PRECAUCION: PARA USO EN EQUIPOS ELECTRONICOS SOLAMENTE
IRAM certificate to IEC 60950-1:2005 + A1:2009
JAPAN TUV R-PSE, Cert. No. JD 50314327, to J60950-1(H26) , J55022(H22),J3000(H25)[15V or less]. Please reference the following website for guidelines on PSE regulations: http://en.globtek.com/importing-ite-and-medical-power-supplies-ac-adaptors-to-japan/
JAPAN TUV R-PSE, Cert. No. JD 50473430, to J62368-1(H30) , J55032(H29),J3000(H25)[15V or less]. Please reference the following website for guidelines on PSE regulations: http://en.globtek.com/importing-ite-and-medical-power-supplies-ac-adaptors-to-japan/
Korea KET KC Mark GT-41080-1817.9-5.9 HU10499-11006A (9V, 12V, 15V)
Korea KET KC Mark GT-41080-1824 HU10499-13012A (18V, 20V, 24V)
Efficiency: complies to section 301 of Energy Independence and Security Act (EISA) complies with Energy Star tier 2 (North America), ECP tier 2 (China), MEPS tier 2 (Australia), Code of Conduct (Europe)
LPS
Limited Power Source 60950
JAPAN TUV Rheinland-PSE GlobTek Inc to J60950-1(H26) , J55022(H22),J3000(H25).Please follow the procedure listed in the following link for proper import to Japan: http://en.globtek.com/importing-to-japan.php.
RCM certificate SAA-160017-EA ; Australia and New Zealand Regulatory Compliance, Mark (http://rcm.standards.org.au/rcmfaq/rcmfaq.htm
RoHS
Specifications of directive 2011/65/EU Annex VI (ROHS-2) with amendment 2015/863-EU (ROHS-3) http://www.ce-mark.com/Rohs%20final.pdf
Saudi Arabia approval GT-41080-18VV-X.XX-Q IEC 60950-2005, output voltage range 5-24V
EN 60335-1:2002+A1:2004+A11:2004+A12:2006+A2:2006+A13:2008+A14:2010+A15:2011
(for GT-41080-1812-W3E only)
Female Barrel 5.5*2.5*11mm, Right Angle without internal Spring Clip & Locking Notch or Equal
316325
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
166902
12.0
1.5
Female Barrel Right Angle, 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
167112
12.0
1.5
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
168184
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
168214
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
169357
12.0
1.5
Female Barrel 5.5*2.1*9.5mm with internal Spring Clip and Locking Notch or Equal
170838
12.0
1.5
8 Pin DIN Plug or Equal
171386
12.0
1.5
Female Barrel Right Angle, 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
173984
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
175138
12.0
1.0
Switchcraft 767K
193400
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
175151
12.0
1.5
Female Barrel 5.0 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
177234
12.0
1.5
Female Barrel 5.5*2.1*9.5mm No internal Spring Clip nor Locking Notch or Equal
128488
12.0
1.5
Female Barrel 5.5*2.1*9.5mm No internal Spring Clip nor Locking Notch or Equal
315874
12.0
1.5
Female Barrel Straight , 5.5*2.1*10mm without internal Spring Clip nor Locking Notch or Equal
192041
12.0
1.5
Female Barrel 5.5*2.5*11mm, Right Angle without internal Spring Clip & Locking Notch or Equal
184253
12.0
1.5
Female Barrel 5.5*2.5*11mm, Right Angle without internal Spring Clip & Locking Notch or Equal
197282
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
198062
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
198073
12.0
1.5
8 Pin Mini DIN Male Plug
199313
12.0
1.5
Female Barrel, Locking, 5.5 * 2.5 * 13.8mm w/ 4.0mm Thumb Screw No Equal
199314
12.0
1.5
Female Barrel 5.5*2.1*12mm No internal Spring Clip nor Locking Notch or Equal
179440
12.0
1.5
Mini-B USB 5 Pin Type "B" or Equal
179931
12.0
1.0
Female Barrel 5.5*2.1*9.5mm No internal Spring Clip nor Locking Notch or Equal
180406
12.0
1.5
Female Barrel 5.5*2.1*9.5mm No internal Spring Clip nor Locking Notch or Equal
181046
12.0
1.5
Female Barrel Right Angle, 5.5*2.1*9.5mm No internal Spring Clip nor Locking Notch or Equal
183129
12.0
1.5
Female Barrel Right Angle, 5.5*2.1*9.15mm No internal Spring Clip nor Locking Notch or Equal
183356
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
183528
12.0
1.5
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
184874
12.0
1.5
Female Barrel 5.5*2.5*13.8mm w/6.5mm Thumb Screw, 760K or Equal mates with PC712A, 712A
288448
12.0
1.5
Female Barrel Straight , 5.5*2.1*10mm without internal Spring Clip nor Locking Notch or Equal
190095
12.0
1.0
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
209307
12.0
1.5
18AWG Wire Cord End Sleeve
209732
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
199777
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
212702
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
227860
12.0
1.5
Female Barrel 5.5 * 2.5 * 10mm with internal Spring Clip and Locking Notch or Equal
229502
12.0
1.5
MOLEX P/N:43645-0200 Micro-fit 3.0 (2) circuit connector housing with 2X Molex P/N: 43030-0007 Female terminal or Equal
240801
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
254958
12.0
1.5
Female Barrel 3.5*1.35*9.0 mm, with Internal Spring Clip and Locking Notch or Equal
262816
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
264547
12.0
1.5
Stripped 20+/-2mm, Tinned 5+/-2mm with Black Thermal Contracting Sleeve or Equal
264552
12.0
1.5
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
177985
12.0
1.5
Female Barrel Right Angle, 5.5*2.1*9.5mm without internal Spring Clip nor Locking Notch or Equal
169658
14.4
0.5
Stripped 50 +/-5mm; with uninsulated #8 ring terminals
191030
15.0
1.2
Female Barrel 3.5*1.1*11mm, Locking , Insert Pin#3511TV200(01) or Equal
195914
15.0
1.2
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
506694
15.0
1.2
Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
137688
15.0
1.2
Socket for interchangeable o/p connectors
149096
15.0
1.2
8-PIN FEMALE KAIPU P/N: FS1-8TK, PINS GOLD PLATED AT 4u
149100
15.0
1.2
Female Barrel 5.0*1.95*8.0mm No internal Spring Clip nor Locking Notch or Equal
162993
15.0
1.2
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
199944
15.0
1.2
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
164358
15.0
1.2
9 POLE D-SUB CONNECTOR, HASCH PLASTIC P/N: DT09A, Metallized (NO EQUIVALENT!)
168342
15.0
1.2
8-Pin Circular Connector, Binder P/N 99-5672-19-08 NO EQUIVALENT!
164357
15.0
1.2
8-PIN RJ-45 connector with a Bubble Boot
178290
18.0
1.0
Female Barrel Right Angle, 5.5*2.1*13mm No internal Spring Clip nor Locking Notch or Equal
214005
18.0
1.0
Female Barrel Right Angle, 5.5*2.1*11mm with internal Spring Clip and Locking Notch or Equal
185458
18.0
1.0
Female Barrel 5.5*2.1*11mm w/ Spring Clip & Locking Notch or Equal
179902
18.0
1.0
Female Barrel, Locking, 5.5 * 2.5 * 18.5mm With Thumb Screw SWITCHCRAFT 761KS12 ONLY
137702
18.0
1.0
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
163512
18.0
1.0
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
137703
18.0
1.0
Molex P/N 43025-0408 Microfit 4 circuit connector (3mm pitch) with Molex Contact 43030-0001 or Shang-Yi C3030HF-2X2P-(X1) housing with Shang Yi C3030F-TPE-A(X1) Terminal. No alternate without engineering and customer approval.
171330
19.0
0.9
Female Barrel 4.0*1.7*9.5mm with internal Spring Clip and Locking Notch or Equal
195916
20.0
0.9
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
195915
20.0
0.9
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
137730
24.0
0.75
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
239539
24.0
0.75
2 Pin FX9
137729
24.0
0.75
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
199803
24.0
0.75
Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
137731
24.0
0.75
Socket for interchangeable o/p connectors
166927
24.0
0.75
Stripped 50 +/-5mm; Tinned 9.5 +/- 2mm or Equal
201182
24.0
0.8
Female Barrel Right Angle, 5.5*2.1*9.5mm without internal Spring Clip nor Locking Notch or Equal
199798
24.0
0.75
Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
163939
24.0
0.8
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
164080
24.0
0.75
Female Barrel 5.5*2.1*11mm w/ Spring Clip & Locking Notch or Equal
164360
24.0
0.75
Female Barrel 4.0*1.7*9.5mm with internal Spring Clip and Locking Notch or Equal
199802
24.0
0.75
Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
24V Class II double insulated 18W (Watt) Interchangeable blade wall plug in Switching Power Supplies updated to latest Korea/Korean standard K 60950-1(2.0)(2011-12), model GT-41080-1824
NOM Mexico Certificate
GT-41080-1824 to NOM-001-SCFI-1993
What is a Plug-in AC-DC Adapter?
Plug in AC-DC adapters are also known as AC Adaptors or AC-DC converters and are a type of external power supply. Some electrical appliances require power but lack the internal components to derive the required voltage and power from mains power. This is where an AC adapter is used to convert the AC current into DC voltage
How Does an AC-DC Adapter Work?
The AC to DC adapter or external power supply consists of a power supply which is enclosed in a housing similar to an AC plug, hence the term plug type, wall plug in, plug-in or plugtop power adapter. The power supply is plugged into the mains socket and the AC Voltage is then converted by the AC to DC adapter power supply into a DC voltage that is fed into the appliance via the output cable connection.