Regulated Switchmode AC-DC Power Supply AC Adaptor
Category
ITE Power Supply
Input Voltage Range (V)
100-240V~, 50-60 Hz
Max Input Current (A)
0.6 A
Max Output Power Rating (W)
18
Output Voltage Range (V)
5-9
Efficiency
V
Ingress Protection
IP52
Size (mm)
43.5 x 74.0 x 35.3
Enclosure
Rating Table
Model Number (Final ordering #/Part No to be defined)
Voltage
Amps (A)
Watts (W)
RFQ
GT-41081-1505*
5
3
15
GT-41081-1805*
5
3.6
18
GT-41081-1806-0.8*
5.2
3
15.6
GT-41081-1506*
6
2.5
15
GT-41081-1806*
6
3
18
GT-41081-1809-2.5*
6.5
2.76
17.94
GT-41081-1809-1.5*
7.5
2.4
18
GT-41081-1809*
9
2
18
GT-41081-1509*
9
1.7
15.3
* (Final ordering #/Part No to be defined)
Specifications
A) ELECTRICAL SPECIFICATIONS:
01. Input Voltage: Specified 90-264 Vac, Nameplate rated: 100-240Vac
02. Input Frequency: Specified 47-63 Hz, Nameplate rated 50-60Hz
03. Output Regulation: +/- 5% measured at the output connector
04. Line Voltage Regulation: +/- 1% typical measured at the output connector
05. Output Ripple (Vp-p): +/-1% or 150 mV whichever is greater, measured at 20 MHz bandwidth with 0.1 uf ceramic capacitor in parallel with 10 uf electrolytic capacitor connected at the end of the output connector at nominal line
06. Turn-ON/OFF Overshoot: 5% maximum, 1 mS typical recovery time for 25% to 50% step load
07. Turn-ON Delay: 1 second typical
08. Hold-Up Time: 8 mS typical @ nominal input voltage and full load
09. Inrush Current: 30A typical at 115VAC input and 60A typical at 230 VAC input
10. Switching Frequency: 65 KHz typical
B) PROTECTION
01. Over-Voltage: Protected Zener clamp across the output
02. Short Circuit: Protected unit will auto recover upon removal of fault
03. Input Protection: Input line fusing
C) SAFETY
01. Dielectric Withstand Voltage: 4242Vdc from primary to secondary
02. Touch Current: <0.25mA @ 240Vac input voltage
03. ROHS 2: Complies with EU 2011/65/EU and GB/T26572-2011
D) OTHER:
01. MTBF: 200,000 Hours @ 25°C ambient temperature
02. Operating Temperature: 0°C to 40°C ambient temperature
03. Humidity: 0% to 90% relative humidity
04. Storage Temperature: -10°C to 80°C
05. Cooling: Convection
E) ENCLOSURE
01. Housing: High impact plastic, 94V0 polycarbonate, non-vented
02. Size: 43.5 x 74.0 x 35.3 +/-1.0mm
03. Markings: Label and/or Pad Printed and/or Molded in the case
INPUT CONNECTOR: Q-Socket (below are available blades configurations which are "not included" (unless stated above); can be purchased separately, package with power supply or as a separate "Q-KIT" if specified
01. United States / Canada / Japan NEMA 1-15P/ IEC PLUG Type A [WORKS IN PLUG B] configuration: NA 2 blades, Class II; US/CA/JP P/N: Q-NA(R) 02. Australian AS 3112 configuration: SAA 2 blade/ IEC TYPE I, Class II; AU P/N: Q-SAA(R) 03. UK BS 1363 configuration: UK 3 blade with dummy Ground/ IEC TYPE G, Class II; GB P/N: Q-UK(R) 04. European CEE 7/16 configuration: Europlug 2 pins/ IEC TYPE C [WORKS IN TYPE E&F], Class II; EU P/N: Q-EU(R) 05. Korean KS C8305 configuration: 2 pins/SIMILAR TO IEC TYPE C, Class II; KR P/N: Q-KR(R) 06. Argentina IRAM 2073 configuration: 2 blades/SIMILAR TO IEC TYPE I; AR P/N: Class II Q-AR(R) 07. China GB 2099 configuration: 2 blades/SIMILAR TO TYPE A, Class II; CN P/N:Q-CN(R) 08. India IS 1293 6A/BS546 configuration: 5A, 3 pins with Dummy Ground, Class II/IEC TYPE D; IN P/N: Q-IN(R) 09. IEC60320/C18 Inlet, Class II; P/N:Q-C18(R) 10. Brazilian NBR6147 configuration: 2 pins, Class II;SIMILAR TO IEC TYPE C BR P/N: Q-BR(R) 11. South Africa SABS164-1, 3 round prongs, Class II + dummy ground, IEC TYPE M P/N: Q-SANS164-1-16A(R) 12. South Africa SABS164-4, 3 round prongs with a notched prong @ 0º, Class II + dummy ground, IEC TYPE M Red, P/N: Q-SANS164-4L-16A(R) 13. South Africa SABS164-4, 3 round prongs with a notched prong @ -53º, Class II + dummy ground, Blue, IEC TYPE M, P/N: Q-SANS164-4C-16A(R) 14. South Africa SABS164-4, 3 round prongs with a notched prong @ +53º, Class II + dummy ground, Black,IEC TYPE M P/N: Q-SANS164-4R-16A(R)
Contact GlobTek for your specific requirements or custom solutions.
Approvals
Logo
Description
No Logo
CB Certificate IEC 60950-1:2005 (2nd Edition), Am 1: 2009, CB report IEC 60950-1:2005 (2nd Edition), Am 1: 2009 and EN 60950-1:2006 + Am 1:2010 + Am 11:2009 + Am 12:2011
CHINA SJ/T 11364-2014, China RoHS Chart: http://en.globtek.com/globtek-rohs.php
UL60950-1, cULus to UL 60950-1, 2nd Edition, 2007-03-27 and CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03
Certification # TC RU AR46.B.69004 Custom Union of Russia, Belarus and Kazakhstan
Indoor Use Only - Mark is on the label or Molded in the case
IP52
Ingress Protection: ?IP52 to IEC60529:2001 Protected against dust - limited ingress (no harmful deposit) and Protected against direct sprays up to 15 degrees from the vertical
JAPAN TUV R-PSE, Cert. No. JD 50471561.pdf, to J62368-1(H30) , J55032(H29), J3000(H25) ,[15V?30V]. Please reference the following website for PSE regulations: http://en.globtek.com/importing-ite-and-medical-power-supplies-ac-adaptors-to-japan/
JAPAN TUV R-PSE, Cert. No. JD 50471561, to J62368-1(H30) , J55032(H29), J3000(H25) ,[30V?60V]. Please reference the following website for PSE regulations: http://en.globtek.com/importing-ite-and-medical-power-supplies-ac-adaptors-to-japan/
JAPAN TUV R-PSE, Cert. No. JD 50471561, to J62368-1(H30) , J55032(H29), J3000(H25) ,[15V or less]. Please reference the following website for PSE regulations: http://en.globtek.com/importing-ite-and-medical-power-supplies-ac-adaptors-to-japan/
Korea KET KC Mark GT-41081-1505 HU10499-15023A (5V Only)
Efficiency: complies to section 301 of Energy Independence and Security Act (EISA) complies with Energy Star tier 2 (North America), ECP tier 2 (China), MEPS tier 2 (Australia), Code of Conduct (Europe)
Japan: Voluntary Control Council for Interference (VCCI)
WEEE: Complies with EU 2012/19/EU (http://ec.europa.eu/environment/waste/weee/index_en.htm)
Mark is on the label or Molded in the case
Popular Products (Stock items)
SKU
Volts Out
Current Out (Amps)
Connector
RFQ
Sample Request
106553
5.0
3.0
DC Power connector, locking, 5.5*2.1mm, 12mm insertion depth; Equiv to S761K & 767K; mates with L722A, PCL722A
175106
5.0
3.0
Female Barrel 3.5*1.35*9.5mm, without Locking Notch nor Spring Clip or Equal
167427
5.0
3.0
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
169830
5.0
2.0
Female Barrel 4.75*1.7*9.5mm or Equal
175507
5.0
3.0
Female Barrel 3.5*1.35*7.5mm, without Locking Notch nor Spring Clip or Equal
170714
5.0
2.6
Stripped 50 +/-5mm; Tinned 9 +/- 2mm or Equal
170761
5.0
3.0
DC Power connector, locking, 5.5*2.1mm, 12mm insertion depth; Equiv to S761K & 767K; mates with L722A, PCL722A
170877
5.0
2.6
Stripped 50 +/-5mm; Tinned 9 +/- 2mm or Equal
173222
5.0
2.0
Female Barrel Right Angle, 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
263395
5.0
3.0
Outer Jacket Stripped 7 +/- 3mm and Wire Stripped & Tinned 2.8 - 4mm NO equivalent
166900
5.0
3.0
DC Power connector, locking, 5.5*2.1mm, 12mm insertion depth; Equiv to S761K & 767K; mates with L722A, PCL722A
176958
5.0
3.0
10 pins plug connector
196267
5.0
3.0
Female Barrel 5.5*2.1*9.5mm with internal Spring Clip and Locking Notch or Equal
198059
5.0
3.0
Outer Jacket Stripped 7 +/- 3mm and Wire Stripped & Tinned 2.8 - 4mm NO equivalent
179328
5.0
3.0
Micro USB type B without resistor
179330
5.0
3.0
Micro USB type B without resistor
180366
5.0
3.0
Female Barrel, Right Angle 3.5 * 1.35 * 9.5mm with internal Spring Clip and Locking Notch or Equal
180862
5.0
3.0
FEMALE BARREL 5.5*2.5*9.5 mm SHOGYO P/N: SCDP443DBNNNBPTG OR EQUIVALENT
180982
5.0
3.0
Female Barrel 3.5*1.3*9.5 mm, with Locking Notch and Spring Clip or Equal
167072
5.0
3.0
FEMALE BARREL 5.5*2.5*9.5 mm SHOGYO P/N: SCDP443DBNNNBPTG OR EQUIVALENT
170599
5.0
3.0
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
165883
5.0
3.0
3 Pin Kycon KPP-3 Locking Plug or Equal
181515
5.0
3.0
Type "A" USB 4 Pin Jack or Equal
246709
5.0
3.0
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
201225
5.0
3.0
Female Barrel Right Angle, 5.5*2.1*11mm with internal Spring Clip and Locking Notch or Equal
213819
5.0
3.0
DC Power connector, locking, 5.5*2.5mm, 12mm insertion depth; Equiv to 761K; mates with L712A, PCL712A
209595
5.0
3.0
DC Power connector, locking, 5.5*2.5mm, 12mm insertion depth; Equiv to 761K; mates with L712A, PCL712A
149595
5.0
3.0
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
186463
5.0
3.0
2x SX0L0C-P09MCC0-0001 ODU MINI-SNAP size 0 Plug and 700.022.208.960.040 cable strain relief (one each) NO Equivalent
184108
5.0
3.0
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
183811
5.0
3.0
Socket for interchangeable o/p connectors
187167
5.0
3.0
Outer Jacket Stripped 7 +/- 3mm and Wire Stripped & Tinned 2.8 - 4mm NO equivalent
181088
5.0
3.0
Female Barrel straight 3.5*1.3*9.5mm, without Locking Notch nor Spring Clip or Equal
137572
5.0
3.0
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
137573
5.0
3.0
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
137576
5.0
3.0
Socket for interchangeable o/p connectors
137579
5.0
3.0
Female Barrel 4.0*1.7*9.5mm Right angle with internal Spring Clip and Locking Notch or Equal
143675
5.0
3.0
Female Barrel 5.5 * 2.5 * 11mm with internal Spring Clip and Locking Notch or Equal
148832
5.0
3.0
Female Barrel Right Angle, 5.5*2.1*11mm with internal Spring Clip and Locking Notch or Equal
149456
5.0
3.0
Female Barrel 3.5*1.35*9.5mm, without Locking Notch nor Spring Clip or Equal
137558
5.0
2.6
Stripped 50 +/-5mm; Tinned 9 +/- 2mm or Equal
238287
5.2
3.0
Micro-B USB 5 Pin Type "B" or Equal
175516
6.0
3.0
Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
187881
6.0
3.0
Female Barrel 3.8*1.35*8mm No internal Spring Clip nor Locking Notch or Equal
137591
6.0
3.0
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
180278
6.0
3.0
Female Barrel 5.5*2.1*11mm WITH internal Spring Clip and Locking Notch or Equal
170844
6.3
2.38
Female Barrel 5.5 * 2.5 * 11mm No internal Spring Clip nor Locking Notch or Equal
198058
6.5
2.76
Circular 2P(5A)
229501
6.5
2.76
Circular 2P(5A)
117658
7.5
2.4
Female Barrel 3.5*1.35*11mm, with Locking Notch and Spring Clip or Equal
196165
7.5
2.4
Female Barrel 5.5*2.1*12.5mm w/Spring Clip and Locking Notch or Equal
165777
7.5
2.4
Female Barrel 5.5*2.1*11mm No internal Spring Clip nor Locking Notch or Equal
How Does an AC-DC Adapter Work?
The AC to DC adapter or external power supply consists of a power supply which is enclosed in a housing similar to an AC plug, hence the term plug type, wall plug in, plug-in or plugtop power adapter. The power supply is plugged into the mains socket and the AC Voltage is then converted by the AC to DC adapter power supply into a DC voltage that is fed into the appliance via the output cable connection.
What is a Plug-in AC-DC Adapter?
Plug in AC-DC adapters are also known as AC Adaptors or AC-DC converters and are a type of external power supply. Some electrical appliances require power but lack the internal components to derive the required voltage and power from mains power. This is where an AC adapter is used to convert the AC current into DC voltage